Master Building Specialties Prices for:Home > Products > Bathroom Partitions > Bradley / Mills > Solid Plastic

Bradley Mills Solid Plastic HDPE Bradmar Toilet Partitions

  • This style provides the most economical solution for heavy traffic and vandalism prone areas. Because it requires no special floor or ceiling construction, installation is easy in new or old buildings. The anti-grip rail provides outstanding rigidity.    
  • Bradmar is fabricated from an advanced formula of 30% post-industrial recycled high density polyethylene (HDPE). Available in over 21 popular colors.  With low maintenance and high vandal resistance, Bradmar is the solution for schools, theme parks, stadiums and arenas - any high-traffic restroom design challenge you have.
  • New! Now available in 100% Post Consumer Recycled HDPE in Moss, Toffee, Beige and Charcoal Gray.
  • Now available in No-Site™ european styling (pictured left) 

Specification / Material Construction 

Construction

  

Bradley / Mills toilet partition Doors, panels and pilasters are constructed from 1" thick High Density Polyethylene (HDPE) resins pressed under high pressure to form a single component. This material is waterproof, non-absorbent and has a self-lubricating surface which resists marks from graffi ti. All plastic components are shipped with a self-adhesive coating for protection during installation. Bradmar ® is available in 21 standard colors.

Panels and Doors

Bradley / Mills toilet partition Panels and doors are fabricated 55" high, all edges are rounded to a 3/16" radius. Panels and doors receive an aluminum heat sink strip fastened to the bottom edge which helps dissipate any applied heat. Each door is pre-drilled to receive an integral hinge assembly. The closing position of each hinge is fully adjustable.

Permaseal Pilasters(Fronts )   

Bradley / Mills baked enamel Pilasters (fronts) feature same interlocking construction and finish as panels; minimum 1-1/4. thick. Constructed of 20 gauge material. Secures to floor by fitting over full-width 16 gauge internal channel. Top bracing of aluminum etched and anodized 1" x 1-1/2. "anti-grip" clamp over fronts and securely held by screws to the front. Partition floor fastenings are concealed by 3" high one-piece shoe of #304 bright annealed stainless steel secured in place with concealed retainer clips Hardware. Restroom partitions shall be provided with all hardware and fastenings to provide a complete installation.

Pilasters and Shoes

Bradley / Mills toilet partitions The floor edge of the pilaster shall be provided with a 5/16" zinc-plated lag screw for leveling. Pilasters are secured to the fl oor using a 3" high, one-piece, type 304 stainless steel shoe with a #4 stain brushed fi nish. Plastic shoes available for select colors.

Hardware

Bradley / Mills toilet partitions standard hardware is constructed from 6463-T-5 heavy-duty aluminum. Compartments are provided with all hardware and stainless steel torx head w/ pin fasteners to complete installation for applications with concrete fl oors and masonry block walls.

Door Hardware

Standard integral hinge system consisting of a 1/2" diameter nylon gravity cam unit with a 3/16" stainless steel center pin (bottom) and a 1/2" nylon rod (top). Strike/keeper is 6" long and is fabricated from heavy-duty extruded aluminum (6463-T-5 alloy) with wraparound fl anges. Strike/keeper is mounted to the pilaster with thru-bolts.

Coat hooks, door bumpers and door pulls are provided in a Zamac alloy with satin fi nish. Integral hinge doors 32"-36" wide are supplied with an individual coat hook, door bumper and door pull. Theft-resistant fasteners are supplied with all hardware.

Brackets

Continuous brackets are fabricated from heavy-duty aluminum, are 54" long and are available in single- or double-ear style. Plastic brackets available for select colors.

Headrail

Etched and anodized aluminum headrail is extruded with an anti-grip profile. It clamps over the pilaster and is secured at the wall with stainless steel brackets.