Knowledge Base:  

You are here: Knowledge Base : BObrick
Page of 2
TB-34 Threaded Metal Inserts Reinforce Door & Stile hardware in all Bobrick Partitions
Bobrick's standard partitions have superior holding power built in, using Commercial Hardware in an unique nohardware- on-the-outside styling. In doors and stiles with particle board core (TrimLine, D
TB-84 COMPARISON OF BOBRICK SIERRA™ SERIES VS. “COLOR-THRU PHENOLIC”
COMPARISON OF BOBRICK SIERRA™ SERIES VS. “COLOR-THRU PHENOLIC” See attached Bulletin for comparisons
TB-14 CAPACITIES OF BOBRICK WASTE RECEPTACLES
CAPACITIES OF BOBRICK WASTE RECEPTACLES See attached Bulletin for  Chart listing capacities of waste receptacles
TB-25 NAPKIN AND TAMPON GUIDE FOR BOBRICK NAPKIN/TAMPON VENDORS
NAPKIN AND TAMPON GUIDE FOR BOBRICK NAPKIN/TAMPON VENDORS See attached Bulletin for  chart of napkins and Tampons for  Bobrick Units.
Tb-44 CAPACITIES OF BOBRICK FOLDED PAPER TOWEL DISPENSERS
CAPACITIES OF BOBRICK FOLDED PAPER TOWEL DISPENSERS A top-quality, two-ply towel, heavily creped and embossed, will yield relatively few towels to the cabinet inch; a hard finished, single-ply towel
Tb-45 BOBRICK WASHROOM EQUIPMENT THAT CONFORM TO U.S. FEDERAL SPECIFICATIONS
The attached Bulletin lists Federal Specifications, Commercial Item Descriptions (CIDs), and the Bobrick Models that may be submitted in appropriate classifications. Selections from this guide should
INSTALLATION INSTRUCTIONS FOR BOBRICK LAMINATED PLASTIC TOILET PARTITIONS 1030 TrimLine™ Series • 1040 Designer™ Series • 1840 FRP™ Series
Installation instructions for BOBRICK  1030,1040 series Partitions (1840 series discontinued)
TB-37 Core material used in Bobrick toilet compartments
1030/1040 Series Particle-board is the substrate for most laminated plastic toilet partitions. It is fabricated of wood chips and flakes embedded in resins. The wood most commonly used in commercial p
TB-77 Sierra Series LEED Certification Program
Sierra Series LEED Certification Program: Environmental sustainability in architectural design can help contain construction costs and/or reduce annual building operating expenses. The Solid Color Re
TB-73 SURFACE BURNING CHARACTERISTICS OF VARIOUS TOILET PARTITION MATERIALS
INDEPENDENT LABORATORY TESTING Samples of different toilet partition materials were sent to independent fire test laboratories for testing and evaluation to determine the relative surface burning cha
TB-60 Cleaning and Maintenance for Laminated Plastic and Solid Phenolic
Bobrick Toilet Partitions, Urinal Screens, and Dressing Compartments are constructed of three different types of material. The three different types of material are: Laminated Plastic, Solid Phenolic,
TB-32 Suggested Mounting Systems for Ceiling hung toilet partitions
Provisions must be in the construction of the building to support ceiling-hung toilet partitions. Structure in ceiling, not furnished by Bobrick, must support at least 200 lb per laminated-plastic par
TB-46 Suggested Mounting Systems for Floor-Anchored and Overhead Braced Toilet Partitions
LEVELING DEVICE The steel-core reinforced stiles of Bobrick floor-anchored and overhead-braced toilet partitions are constructed with an 11-gauge steel core welded to a 3/8'' thick leveling bar. Each
TB-55 Locating Accessories inside the Toilet Partition
PARTITION-MOUNTED ACCESSORIES • Accessories in a toilet partition should be positioned to be within easy reach from the toilet. All accessories should be accessible on a side wall or partition. • Bob
TB-78 Impact Resistance of Various Toilet Partition Materials
INDEPENDENT LABORATORY TESTING Three samples of six different partition materials [Powder-Coated Metal (Metal), High Density Polyethylene (HDPE), Polypropylene (Polyprop), Plastic Laminate (P-Lam), So
TB-79 SCRATCH RESISTANCE OF VARIOUS TOILET PARTITION MATERIALS
INDEPENDENT LABORATORY TESTING Three samples of six different partition materials [Powder-Coated Metal (Metal), High Density Polyethylene (HDPE), Polypropylene (Polyprop), Plastic Laminate (P-Lam), So
TB-80 GRAFFITI RESISTANCE OF VARIOUS TOILET PARTITION MATERIALS
INDEPENDENT LABORATORY TESTING Three samples of different toilet partition materials [Powder-Coated Metal (Metal), High Density Polyethylene (HDPE), Polypropylene (Polyprop), Plastic Laminate (P-Lam),
TB-81 SIERRA™ SERIES SOLID COLOR REINFORCED COMPOSITE TOILET PARTITION REPAIRABILITY
Bobrick Sierra™ Series Solid Color Reinforced Composite (SCRC) is a solid color material with excellent scratch-resistant properties. However, as with any material, intentional acts of vandalism with
TB-82 GENERAL CLEANING AND MAINTENANCE OF 1090 SIERRA™ SERIES TOILET PARTITIONS
FOR ROUTINE CLEANING: Use a soft cloth moistened with mild soap, detergent, or all purpose cleaner to wipe partition surface. Wipe off cleaner residue off using a clean cloth and water. Ensure that p
TB-87 Toilet Partition material LEED information Program
Leadership in Energy and Environmental Design (LED) Certification Program Information Version 2.2: The LEED Rating Systems are developed by the United States Green Building Council ("USGBC"). It is a