TB-46 Suggested Mounting Systems for Floor-Anchored and Overhead Braced Toilet Partitions
LEVELING DEVICE The steel-core reinforced stiles of Bobrick floor-anchored and overhead-braced toilet partitions are constructed with an 11-gauge steel core welded to a 3/8'' thick leveling bar. Each |
TB-73 SURFACE BURNING CHARACTERISTICS OF VARIOUS TOILET PARTITION MATERIALS
INDEPENDENT LABORATORY TESTING Samples of different toilet partition materials were sent to independent fire test laboratories for testing and evaluation to determine the relative surface burning cha |
TB-32 Suggested Mounting Systems for Ceiling hung toilet partitions
Provisions must be in the construction of the building to support ceiling-hung toilet partitions. Structure in ceiling, not furnished by Bobrick, must support at least 200 lb per laminated-plastic par |
TB-55 Locating Accessories inside the Toilet Partition
PARTITION-MOUNTED ACCESSORIES • Accessories in a toilet partition should be positioned to be within easy reach from the toilet. All accessories should be accessible on a side wall or partition. • Bob |
TB-86 2006 MODEL CODE CHANGES
The 2006 editions of the International Code Council (ICC) plumbing (IPC) and building (IBC) codes, and the National Fire Protection Association® (NFPA) NFPA 101® Life Safety Code® are now available. A |
CSI Specification Guidelines Section 15400
Specifier notes are shown in italics and should be deleted from
the final document. Generally all of the manufacturer’s products in
this category are listed and the specifier must take care to dele |
Scranton products Technical Data
TECHNICAL SPECIFICATIONS High Density Polyethylene (HDPE)* has been independently laboratory tested, and are unaffected when exposed to the following substances:
• Acetic Acid |
Bradley Lenox Locker Installation Instructions
Lenox Locker Installation instructions
Step 1: Optional Locker Base Installation
IMPORTANT: Make sure the base is square AND level before anchoring to the floor (the
base may be square but not |
Bradley Lenox Locker Bench Installation
Bradley Lenox Locker Bench Installation ( With or without doors )
Pre-Installation Information
Tools Required
• Tape measure, level and shims
• Power Drill
• Pop rivet gun |
Bradley Panelon Modular Shower System Technical Data
Bradley Panelon Showers — Prefabricated Modular Shower Systems
Specifications
Materials
Panelon showers constructed of type 304 stainless steel. Shower panels and stanchions are 16 gau |
Bradley Column beach Shower COL-6C
Column Showers 6-Person
COL-6C
Specifications
Materials
All exposed parts are type 304 stainless steel or polished chrome-plated brass. Valve manifold is cast brass. Drain fitting is c |
Bradley Economy Wall Shower, WS-2W, WS-3W
SPAN style="FONT-WEIGHT: bold; FONT-SIZE: 12pt; FONT-FAMILY: Arial">
Econo-Wall Showers
WS-2W, WS-3W
• Completely Preassembled Shower Unit
• Hydrostatically Tested to 150 PSI
• Ready fo |
Modesty Module Showers Models 4000 thru 4036 & Model 4044
Modesty Module Showers
Models 4000 thru 4036 & Model 4044
(IMPORTANT: Signed approvals are required prior to fabrication.)
• Unit Complete with Curtain and Necessary Hardware |
Modesty Module Showers Models 4000 thru 4036 & Model 4044
Installation Instructions
Step 1: Install floor anchors
1. Install your Bradley shower as instructed on the shower installation instructions provided with your new shower.
2. Check dimensions on |
Bradley Lenox Pedestal Bench Installation
Bradley Lenox Locker Pedestal Bench Installation
1. Position each pedestal on the underside of the bench. Mark the hole locations and remove the pedestals. Using a 3/16" drill bit, drill 1/2" deep |
Bradley Column beach Shower COL-5C, COL-4C, COL-3C, COL-2C
Column Showers 2- to 5-Person
COL-5C, COL-4C, COL-3C, COL-2C
• One Set of Supply Connections Required for Five Stations
• Preassembled, Complete with Drain Fitting
Specifications
Ma |